News
Oscillating Tool development (v.2)
|
New development for the Oscillating Tool. The
Double Triple Oscillating
knife allows for a
doubled tripled
output for rubber strips. The tool can be set to pre-specified rubber widths (available at Customers request). |
 |
| video of 500 x 500 mm plate (strips are 7 mm wide) process time 71 strips in 2 minutes | |
| CP running at F30000 (speed) cutting Rubber strips | |
| R600 cutting Rubber | |
IADD-FSEA Odyssey May 2011, Nashville
 |
We would like to thank all visitors at the IADD-FSEA Odyssey show in Nashville.
We were very much encouraged by the favourable comments on the versatility and potential for productivity gain by everyone who visited our booth. For more information about CombiPro in the USA please contact Simon Song at SDS USA Inc. SDS USA Inc. 97 Oak St. Norwood, NJ 07648 Phone: 201-750-2114 ext:201 www.iBEND.net |
 |
Rubber cutting results at the Odyssey Show in Nashville |
 |
Nicking Tool on CP1214 at the Odyssey Show in Nashville |
 |
Clip-on cover for CombiPro Nicking. |
Installation CP1208 at Seal-T
Successful Installation of the CombiPro 1208 at Seal-T, in Moscow, Russia. Seal-T will use the CP for samplemaking, rubber cutting and milling, adding value to their already fully automated Die Shop. We would like to take this opportunity to thank all people at Seal-T for choosing CombiPro and wish them all the best!
 |
|
 |
Nicking Tool development
New development for the Nicking application. New cover, protects users and the CombiPro's moving parts. A video showing the tool in action is available in the Gallery section have a look.
 |
Customer feedback
A customer using CombiPro 1208 for Rubber Cutting send us some interesting pictures... CP cutting accurate shapes with interesting geometries.
 |
|
 |
Open House Fustel Service
Successful demonstration of the CombiPro at the Fustel Service Open House in Milan, Italy. We would like to take this opportunity to thank Rocco Cafarelli and his colleagues for the Hospitality and of course all visitors that came over to have a look at the CombiPro and its potential. Successfully showcasing the extended possibilities of the CombiPro doing samplemaking, cutting ejection rubber for dieboards and even nicking.
.JPG) |
|
.JPG) |
|
.JPG) |
|
.JPG) |
|
.JPG) |
|
.JPG) |
|
.JPG) |
Macropak 2010
Successful demonstration of the CombiPro at the Macropak 2010 in Utrecht, The Netherlands. Demonstrating the all new CP0705 with a working area of 700 x 500 mm , Creasing tools, Cutting tools and Auto-Sensor Positioning tool to process pre-printed samples and short run productions.
 |
|
 |
|
 |
Empack 2009
Successful demonstration of the CombiPro at the Empack 2009 in Madrid. Demonstrating the Auto-Sensor Positioning tool to process pre-printed samples and short run productions.
 |
|
 |
|
 |
ESU Technology Forum 2009
We would like to thank all visitors to our stand at the ESU Technology Forum 2009. We successfully introduced the new CombiPro. General response was great and most people were really surprised to see the CombiPro Nicking a die board. (see video)
 |
|
 |
|
 |
|
 |
|
 |
Exhibitions
 |
Open Day, Nottingham 09-12 > 10-12, Nottingham (UK)
A Special Open Day showcasing the latest in Diemaking technology. |
 |
Visit us at the Empack Madrid, 18 - 19 November 2009. And see the CombiPro in action! |
 |
Visit us at the ESU Technology Forum 11 - 12 September 2009. And see the CombiPro in action! Hall 2 stand 20 |
